Exploiting Radiant Energy on Electrical Conductors - Free Energy from Electrical Circuits

When a high voltage and high frequency electrical conductor is placed on it, it is interrupted by a spark gap, causing the conductor to emit electrical radiation. This type of electricity is also called radiant energy from electronic circuits. Edwin V. Gray once exploited this type of radiant energy, but separated the normal current to create "cold electricity" (called "positive separation").

Edwin V. Gray's circuit is very difficult to manufacture. But if someone is proficient in the method and nature, there will be many people who need them, because "cold electricity" has healing properties and is applied to many other hidden technologies.

To exploit radiant energy more easily, and at the same time serve the needs of electricity for the home, I would like to introduce a method of exploiting radiant energy from an electric circuit since 1923. It is from electrical engineer Frank Wyatt Prentice from Pennsylvania, USA.

# Circuit diagram

1/ Basic diagram and explanation:

Frank Prentice's diagram of harnessing radiant energy in an electric circuit

This diagram consists of 2 stages. Stage 1 is to create high voltage, high frequency from a normal power source. This is done by a transformer and an oscillator of capacitors and coils.

At first, the spark gap is connected. When the circuit is running, it generates a high voltage, enough to get the breakdown voltage across the spark gap, then the spark gap is created by using a screwdriver to remove the contacts.

When the spark gap is running, the voltage and frequency are increased again. This structure is quite similar to the Tesla coil (Tesla transformer). Remember that the capacitance of the capacitor must be high to set the breakdown voltage, and it is a rotating capacitor to adjust the frequency.

When the circuit is running, it only has simple components as a load, which will consume very little power. This is also seen in the Tesla coil, which can use a battery as an input and still operate, creating a spark discharge.

Note: The transformer in the diagram is an air core transformer, not a ferrite core transformer, or other solid state core.

Here are the two original diagrams:

r/plasma_pi - Original diagram 1: Generating high voltage and high frequency
Original diagram 1: Generating high voltage and high frequency
r/plasma_pi - Original diagram 2: Exploiting and using radiant energy
Original diagram 2: Exploiting and using radiant energy

🔺 See more details: Harnessing Radiant Energy in Electric Circuits by Frank Prentice.

When the high voltage is generated on the conductor acting as the Radiant Energy Emitting Antenna, marked as segment AB on the diagram, it is again increased in frequency and voltage through the spark gap connected near the ground.

Section AB will emit radiant energy. To capture this energy, a closed loop oscillating antenna is needed. This is difficult and expensive in today's era.

The closed loop antenna is like a bicycle rim cut out to make a Radio Antenna for TV in the old days (if anyone who lived in the 90s will remember). The bicycle rim was cut out to temporarily replace the original Antenna consisting of broken horizontal bars.

Many such loop antennas are needed to be connected in parallel with the radiant energy emitting wire, that is, segment AB will go through the center of the circles. This is difficult to do in today's world, and very cumbersome when the urbanization process to establish the New World Order is reaching the totalitarian stage.

For that reason, I propose the solution of using coaxial cable to replace the structure of collecting radiant energy using loop antennas.

2/ Circuit diagram using coaxial cable:

Use coaxial cables instead of loop antennas to exploit radiant energy more easily
Use coaxial cables instead of loop antennas to exploit radiant energy more easily

With the above diagram, the core of the coaxial cable is the AB wire in the original circuit diagram. The "Woven copper shield" layer has a mesh shape, this is where the radiant energy is collected, and is transferred to the coil and capacitor to create voltage potential. The resulting voltage is very high because the AB section is radiating a large amount of energy.

This voltage will be brought down to a lower voltage by the step-down transformer (numbered 27), and the frequency will be adjusted to suit the consuming electrical equipment. Induction motors will not be suitable for voltages with too high frequencies. That is why it is necessary to step down the voltage and change the frequency by means of a rotating capacitor.

According to the diagram, the radiation energy received will go into wire 26, to the high voltage primary coil 27', then to capacitor 29 and ground 31 .

🔺 Important noteTesla coil, but it is an inverted Tesla coil.

If I did not mention that note, many people would not be able to successfully build this device.

# Equipment to buy and other notes

* Next important note:

You can buy a dedicated spark gap device, but for this circuit, at first leave it in contact until the capacitor is fully charged and then slowly loosen it to create a spark gap.

Ground with a long copper wall, use as many rods as possible, deeper than 1.5 m and keep moist. If not long enough, dig a hole and put the copper rod in, water and keep moist, pay attention to electrical safety.

The AB wire can be extracted from the output of the secondary coil on the famous Tesla transformer (Tesla coil). If you have experience with Tesla coils, then you only need to buy more coaxial cables and grounded copper bars to be able to exploit free energy. To get diverse electricity, it is necessary to convert by lowering the voltage in the way of the reverse Tesla coil. Then it is necessary to convert more as shown in the diagram. However, it is possible to use a battery to store electricity through the charger to enter the inverter, creating normal AC electricity.

If I have the opportunity, I will present how to exploit free energy on the Tesla coil in more detail.

Be careful with high voltage when using a normal power source to supply the transformer.

🔺 Free energy has many simple and effective methods based on the improvements of experts when finding hidden technologies. Such a set of books for you to order:

⭐ An additional book series containing easy methods to create free energy generators, and this series also contains other technologies, including Tesla technology.
Here is the book: 👉 Easy Power Plan Will Change Our World Forever

📖 That book may contain more advanced free energy technology in the modern version.

# Final words

The method of exploiting radiant energy from electric circuits is demonstrated by many experts on forums, this has been done for a long time. However, few people know, although the benefits of free energy are very large. The reason is because the educational program has been controlled, at the same time the suppression of free energy in many ways.

What I mean is that the radiant energy from the electric circuit actually works but few people understand it, even when successfully building this generator. Actually, this is the technology of radiant energy emitted at the conductor of the electric circuit with the Ether field collapsing at a very high frequency, related to the nature of light and the true nature of matter. A thorough explanation is too long and should not be presented here.

But basically, this radiant energy is emitted based on electric lines of force perpendicular to the circular conductor, which are radial electric lines of force with the center being the axis of the conductor.

Charles Proteus Steinmetz's model of electricity and magnetism on the conductor says that. Without C.P Steinmetz, we might still be using oil lamps today because the problem of power transmission and distribution requires Steinmetz's solution.

Charles Proteus Steinmetz's Electrical Structure of the Ether - Diagram of the Electric Field of a Current-Carrying Conductor
Charles Proteus Steinmetz's Electrical Structure of the Ether - Diagram of the Electric Field of a Current-Carrying Conductor

The dielectric and magnetic structures in Ether will be the basis for explaining the phenomenon of radiant energy from electronic circuits. Electricity is the flow of fields, NOT electrons. Current don’t exist inside the conductor. Current exists in the SPACE surrounding the conductor.

Although Nikola Tesla invented many patents, to apply them in practice, other scientists are needed. Journalists say that C.P Steinmetz was hired by large corporations to decode Tesla's patents. However, I myself have not seen C.P Steinmetz decode Tesla's patents in any scientific work, only books on electrical theory to set up AC power systems and as a basis for developing other technologies.

⭐ Related articles: Tartaria - Radiant Energy - Tracing the Origin of Tesla Technology.

Post a Comment